Start with the right block and a thickness check
The Pepetools oval bezel forming block is a dedicated tool for shaping bezel wire into oval settings for faceted stones and certain cabochons. It combines a hardened steel block with eight oval holes and a matching punch, so you can form consistent curves without freehand bending.
Before you begin, confirm your bezel material thickness. The block is rated for a maximum material thickness of 18 gauge. If your bezel wire or sheet is thicker, the punch and hole may not seat properly, and you risk distorting the block or the bezel. For most oval cabochon settings, 18 gauge or thinner is the practical range.
Block specifications that affect your setup
- Oval Bezel Forming Block w/ Punch - 8 Holes, Large Sizes: Block dimensions are 119mm tall x 132mm wide x 28mm thick, with a 140mm overall length including a 20mm diameter handle. These dimensions tell you how much bench space the block needs and how the handle fits your hand during forming.

Oval Bezel Forming Block w/ Punch - 8 Holes, Large Sizes - Oval Bezel Forming Block w/ Punch - 8 Holes, Large Sizes: The block weighs 14lbs. A heavier block stays put during punching, but you may prefer to secure it or work at a stable bench.
- Oval Bezel Forming Block w/ Punch - 8 Holes, Large Sizes: The block features 8 oval holes cut at a 75% ratio, adhering to the standard 17° angle. The 75% ratio and 17° angle are the geometry that shapes the bezel's taper and curve for oval stones.
Choose the hole that matches your stone
The block has eight oval holes in large sizes. The supplied information includes a table with hole numbers and their length and width in millimeters, but the full table is not reproduced here. To select the right hole, measure your oval cabochon's length and width, then match those dimensions to the hole that gives a snug fit around the stone without forcing it.
Because the holes are cut at a 75% ratio, the length-to-width proportion is fixed. If your stone's proportions differ significantly, you may need to adjust the bezel after forming or choose a different setting approach. For a large oval bezel stone setting, start with the hole closest to your stone's footprint and test-fit with a piece of bezel wire before committing.
How to form an oval bezel with the block and punch
- 1. Anneal your bezel material: Soften the metal so it bends without cracking. This is especially important for thicker gauges near the 18-gauge limit.
- 2. Select the hole: Place your oval cabochon over the holes to find the one that matches its length and width. The stone should sit into the hole slightly, not fall through.
- 3. Position the bezel: Center the bezel strip over the chosen hole, with the decorative side facing down if you want the curve to form inward.
- 4. Seat the punch: Insert the matching oval punch into the hole, aligning it with the bezel. The punch is cut at a 17° angle to match the hole.
- 5. Press or tap evenly: Apply steady pressure or light taps to drive the punch and form the bezel around the hole's contour. Work gradually and check the shape as you go.
- 6. Test-fit the stone: Remove the bezel and check that the stone sits evenly. If the bezel is too tight or loose, adjust with pliers or try the next hole size.
Punch care and replacement
The supplied information notes that punches are susceptible to breakage during regular use, and replacement punches are available for all blocks. To prolong punch life, avoid using excessive force, keep the punch aligned with the hole, and store it separately to prevent damage to the tip.
If a punch becomes damaged, replace it rather than continuing to use it, as a deformed punch can mar the bezel or damage the block. The block itself is made from precision hardened tool steel and EDM machined, which the manufacturer states will withstand the test of time due to its durable material and manufacturing processes.
What the supplied information does not cover
The supplied information does not include detailed operating instructions, recommended annealing temperatures, or specific step-by-step procedures from the manufacturer. It also does not provide a full hole-size table in the excerpt. Always defer to any manufacturer instructions that come with your tool, and use the hole dimensions provided on the product page to match your stone.
If you are unsure whether your bezel material is compatible, test with a small piece first. The block is designed for bezel settings, but the maximum material thickness of 18 gauge is a hard limit based on the supplied specifications.

